* Estimated delivery times start from the date of shipment, excluding processing time.
* Actual delivery times may vary due to holidays, weather conditions, or customs delays.
Ingyenes szabványos szállítás 9.9 $ feletti rendelés esetén
Visszatérítési politika
A termékek visszaküldését 40 napon belül elfogadjuk a termék átvételének dátumától számítva. A testreszabott termékeket nem lehet visszaküldeni vagy kicserélni. Az e-ajándék kártyával vásárolt termékek csak cserélhetők; a visszatérítés nem alkalmazható.
Ingyenes ajándék
Üdvözöljük a Roymall-ban, a prémium áruház ajándékok vásárlásának szakmai weboldalán. Nagyra értékeljük és köszönjük a támogatásodat, és hálánk jeléül extra izgalmat adunk a vásárlásaidhoz. Amikor nálunk vásárolsz, nemcsak kiváló minőségű termékeket kapsz, amelyek javítják az életminőségedet, hanem minden rendelésed mellé egy exkluzív ingyenes ajándékot is kapsz. Készen állsz a gyűjteményünk felfedezésére és a tökéletes ajándékok megtalálására? Böngéssz a prémium áruház termékeink között, add le a rendelésed, és várd az ingyenes ajándékod izgalmát, amely a vásárlásoddal együtt érkezik.
Szállítási politika
Keményen dolgozunk azon, hogy a rendelésedet követően biztonságosan kiszállítsuk a termékeket. A szállítási részleteket a visszaigazoló e-mailben kapod meg.A legtöbb esetben a rendeléseket 2 napon belül feldolgozzuk. Különleges körülmények között a késés a következő lehet: Ha szombaton, vasárnap vagy ünnepnapon rendelsz, a rendelésed 2 napot késik.Általában 5-7 munkanap (hétfőtől péntekig) szükséges, ha nincs késés a repülőjáratban vagy más környezeti tényezők miatt.Mivel szállítási szolgáltatásunk világszerte elérhető, a szállítási idő a helyzetedtől függ, így néhány napig is eltarthat, és ha távoli területen vagy országban élsz, kérjük, legyél türelemmel.
1. Visszatérítési és csere politika
Csak a roymall.com oldalon vásárolt termékeket fogadjuk vissza. Ha helyi disztribútornál vagy más kiskereskedőnél vásároltál, nem tudod visszaküldeni a terméket hozzánk.A végleges eladású termékeket vagy ingyenes ajándékokat nem lehet visszaküldeni.A visszaküldéshez a terméknek használatlannak és eredeti állapotában kell lennie. Eredeti csomagolásban kell lennie.Miután megkaptad tőlünk a visszaküldési utasításokat, csomagold be a visszaküldendő termékeket, és hagyd a csomagot a helyi postán vagy más futárnál.A visszaküldött vagy cserélt terméket 3-5 munkanapon belül feldolgozzuk, miután megkaptuk. A visszatérítést automatikusan feldolgozzuk és jóváírjuk az eredeti fizetési módodra.Nem fogadunk el visszaküldést vagy cserét, ha a termék egyedi gyártású, beleértve az egyedi méretet, színt vagy nyomtatást.További segítségre van szükséged? Lépj velünk kapcsolatba. service@roymall.com vagy Whatsapp: +8619359849471
2. Visszatérítési politika
Teljes visszatérítést vagy 100% bolti kreditet kapsz, miután megkaptuk és ellenőriztük a visszaküldött csomagot. A visszatérítést automatikusan feldolgozzuk és jóváírjuk az eredeti fizetési módodra.Kérjük, vedd figyelembe, hogy a szállítási költségek és minden vám vagy díj nem visszatéríthető. A további szállítási költségek nem visszatéríthetők, miután a csomagot kiszállítottuk. Felelős vagy ezen díjak fizetéséért, és nem tudunk eltekinteni tőlük, vagy visszatéríteni, még akkor sem, ha a rendelést visszaküldöd hozzánk.Ha bármilyen problémád van a visszatérítési folyamattal, lépj velünk kapcsolatba. service@roymall.com vagy Whatsapp: +8619359849471
Description: Item Name:3CH LED Light Switch System Material:plastic and electronic components Color:black Size:190mm length Compatible with: RC Model Cars It can be connected to a single or double set of lights
How To Use: Put the piug of the servo on the remote control board into the third channel of the receiver,then you can control the light switch You can also plug into a "receiver powered" light(means that the light can be directed inserted on the receiver),the board has a boost regulator.,can bring 12 numbers 5mm led lights
Package included: 1X 190mm 3CH LED Light Switch System
not bad, I found that it would work if I only take the lead off then plug it back in again it would work ok , I couldn’t just leave it in the receiver, it would need unplugging and plugging back in , not sure why that is. it got the truck done.
not bad, I found that it would work if I only take the lead off then plug it back in again it would work ok , I couldn’t just leave it in the receiver, it would need unplugging and plugging back in , not sure why that is. it got the truck done.
not bad, I found that it would work if I only take the lead off then plug it back in again it would work ok , I couldn’t just leave it in the receiver, it would need unplugging and plugging back in , not sure why that is. it got the truck done.
I am going to give this product five stars. you can tell that this on-off switches made with high-grade materials. You can also tell that it is well put together and should stand the test of time. I have installed it in my gmade Komodo and it works perfectly. Actually comes with five separate modes. Two separate sides of light systems can be applied. Side A and side B is what we will call them. The modes are as follows. Mode one. Side A side B both off. Mode 2 side A on side B off. mode 3 side A side B on. Mode 4 side A on and B on at the same time. mode 5 is demo mode and is a spectacular light show which includes side A and side B. that leads us to the one thing I think this product definitely could have used and that's some instructions. having to figure this one out on my own was not easy. however, I do not think that this takes away from any of its qualities that reflect this products five star rating. definitely worth every penny and then some..!!
I am going to give this product five stars. you can tell that this on-off switches made with high-grade materials. You can also tell that it is well put together and should stand the test of time. I have installed it in my gmade Komodo and it works perfectly. Actually comes with five separate modes. Two separate sides of light systems can be applied. Side A and side B is what we will call them. The modes are as follows. Mode one. Side A side B both off. Mode 2 side A on side B off. mode 3 side A side B on. Mode 4 side A on and B on at the same time. mode 5 is demo mode and is a spectacular light show which includes side A and side B. that leads us to the one thing I think this product definitely could have used and that's some instructions. having to figure this one out on my own was not easy. however, I do not think that this takes away from any of its qualities that reflect this products five star rating. definitely worth every penny and then some..!!
I am going to give this product five stars. you can tell that this on-off switches made with high-grade materials. You can also tell that it is well put together and should stand the test of time. I have installed it in my gmade Komodo and it works perfectly. Actually comes with five separate modes. Two separate sides of light systems can be applied. Side A and side B is what we will call them. The modes are as follows. Mode one. Side A side B both off. Mode 2 side A on side B off. mode 3 side A side B on. Mode 4 side A on and B on at the same time. mode 5 is demo mode and is a spectacular light show which includes side A and side B. that leads us to the one thing I think this product definitely could have used and that's some instructions. having to figure this one out on my own was not easy. however, I do not think that this takes away from any of its qualities that reflect this products five star rating. definitely worth every penny and then some..!!
Tips:For questions about your order, place of delivery, product discount, taxation, delivery time, warranty, shipping, payment, exchange rate, and other questions unrelated to the product, please contact customer service.
showing 1-18 of 18|
Show Original
A part of the QA has been auto-translated.
0
Q:
Is this a simple switch. Without some that offer flashing. I just want on-off,
Is this a simple switch. Without some that offer flashing. I just want on-off,
Can somebody write a decent connection guide?
In the description says plug the led board to Servo which is channel 1 not channel 3! I tested diffrent types of connections and the only way led board is working is plugging it to channel 1. First full left full right turns port1 on. Then port1 off port2 on, next 2 ports on and last flashing demo mode. Finally, all off. The problem is led board not works with my dumborc 3th channel at all. And if I plug it to Servo channel 1 then where should I plug steering Servo?
Can somebody write a decent connection guide?
In the description says plug the led board to Servo which is channel 1 not channel 3! I tested diffrent types of connections and the only way led board is working is plugging it to channel 1. First full left full right turns port1 on. Then port1 off port2 on, next 2 ports on and last flashing demo mode. Finally, all off. The problem is led board not works with my dumborc 3th channel at all. And if I plug it to Servo channel 1 then where should I plug steering Servo?
The servo is connected with channel 1,esc with channel 2,ch3 switch line with channel 3
The servo is connected with channel 1,esc with channel 2,ch3 switch line with channel 3
Answered by Quaffheep1712 on 14/08/2020Helpful (0)
0
Q:
What is the output voltage of this device. As I am looking at different LED lights for my boat and they are either 3V or 6V. The battery I will be using is a LIPO 7V.
What is the output voltage of this device. As I am looking at different LED lights for my boat and they are either 3V or 6V. The battery I will be using is a LIPO 7V.
You plug this switch to receiver to channel 3 , and then you control it with transmitter channel 3, the switch has 2 output, when you press 1x channel 3 on transmitter led 1 turns on, on second press Led 1+led 2 turns on, on third press led will flash, on forth pres light will go off.....ok??
You plug this switch to receiver to channel 3 , and then you control it with transmitter channel 3, the switch has 2 output, when you press 1x channel 3 on transmitter led 1 turns on, on second press Led 1+led 2 turns on, on third press led will flash, on forth pres light will go off.....ok??
You plug this switch to receiver to channel 3 , and then you control it with transmitter channel 3, the switch has 2 output, when you press 1x channel 3 on transmitter led 1 turns on, on second press Led 1+led 2 turns on, on third press led will flash, on forth pres light will go off.....ok??
You plug this switch to receiver to channel 3 , and then you control it with transmitter channel 3, the switch has 2 output, when you press 1x channel 3 on transmitter led 1 turns on, on second press Led 1+led 2 turns on, on third press led will flash, on forth pres light will go off.....ok??
Answered by Runner on 12/02/2022Helpful (0)
0
Q:
Hello. I want to know how to install this light switch system? I have a WPL MN99 and MN99s RC. I will pair it with dumborc remote. I also got a new ESC. Please help. Rookie in RC world. Thank you in advance.
Hello. I want to know how to install this light switch system? I have a WPL MN99 and MN99s RC. I will pair it with dumborc remote. I also got a new ESC. Please help. Rookie in RC world. Thank you in advance.
You plug this switch to receiver to channel 3 , and then you control it with transmitter channel 3, the switch has 2 output, when you press 1x channel 3 on transmitter led 1 turns on, on second press Led 1+led 2 turns on, on third press led will flash, on forth pres light will go off.....ok??
You plug this switch to receiver to channel 3 , and then you control it with transmitter channel 3, the switch has 2 output, when you press 1x channel 3 on transmitter led 1 turns on, on second press Led 1+led 2 turns on, on third press led will flash, on forth pres light will go off.....ok??
the output voltage is again around 5v....you need to use LED wit resistor to work....only LED will die...depends of what color LED you using..check on google...different LED need different voltage....
the output voltage is again around 5v....you need to use LED wit resistor to work....only LED will die...depends of what color LED you using..check on google...different LED need different voltage....
You plug this switch to receiver to channel 3 , and then you control it with transmitter channel 3, the switch has 2 output, when you press 1x channel 3 on transmitter led 1 turns on, on second press Led 1+led 2 turns on, on third press led will flash, on forth pres light will go off.....ok??
You plug this switch to receiver to channel 3 , and then you control it with transmitter channel 3, the switch has 2 output, when you press 1x channel 3 on transmitter led 1 turns on, on second press Led 1+led 2 turns on, on third press led will flash, on forth pres light will go off.....ok??
Answered by Runner on 12/02/2022Helpful (0)
0
Q:
The instructions are vague, technical specifications noexistent. If I can answer my own question I will provide some findings, however, before trying to identify tbe components to determine these values, what are the minimum and maximum voltage and current that can be switched? (Given ranges of some transmitter or BEC values they could be 3-8 VDC at a current of 50mA to 3A)
The instructions are vague, technical specifications noexistent. If I can answer my own question I will provide some findings, however, before trying to identify tbe components to determine these values, what are the minimum and maximum voltage and current that can be switched? (Given ranges of some transmitter or BEC values they could be 3-8 VDC at a current of 50mA to 3A)
not 100% sure of the max and min voltages, it does work with all of my surface rx's @5-6v 3rd channel is recommended. if you use channel 1, you'll need a splitter so this switch and your steering servo are both connected to the rx. once connected this way, full left turn followed by full right turn should activate, cycle throug modes, and deactivate this device.
not 100% sure of the max and min voltages, it does work with all of my surface rx's @5-6v 3rd channel is recommended. if you use channel 1, you'll need a splitter so this switch and your steering servo are both connected to the rx. once connected this way, full left turn followed by full right turn should activate, cycle throug modes, and deactivate this device.
Answered by mobilefrag on 31/10/2022Helpful (0)
0
Q:
will this work on AUSTAR LED Light Aluminum Alloy Frame For CC01/D90/SCX10/4WD RC Car Parts - Red Blue?
will this work on AUSTAR LED Light Aluminum Alloy Frame For CC01/D90/SCX10/4WD RC Car Parts - Red Blue?
Can this device be used to switch from one camera sending its signal to the VTX to another? Please submit a circuit diagram for this an most basic configurations. The current instructions are confusing! Thanks. Jim
Can this device be used to switch from one camera sending its signal to the VTX to another? Please submit a circuit diagram for this an most basic configurations. The current instructions are confusing! Thanks. Jim
Today I got 3 pieces of it. And it switches sometimes, sometimes not and it comes the what the reler gives out so good 6 volts. How is there to hold a LED, the Brent so immediately through. Total rubbish. I can take a servo electronics and convert it.
Habe heute 3 Stück davon bekommen. Und es schaltet mal, mal nicht und es kommt das was das Reler raus gibt also gut 6 Volt. Wie soll da eine LED halten, die Brent ja sofort durch. Totaler Müll. Da kann ich eine Servo Elektronik nehmen und umbauen.
no voltage coming out? I get voltage all the way to the board which is about 5.6 volts. Once I place the probes to the 4 different contacts, no voltage. I have purchased three of them and still none of them have any voltage coming out?
no voltage coming out? I get voltage all the way to the board which is about 5.6 volts. Once I place the probes to the 4 different contacts, no voltage. I have purchased three of them and still none of them have any voltage coming out?
You plug this switch to receiver to channel 3 , and then you control it with transmitter channel 3, the switch has 2 output, when you press 1x channel 3 on transmitter led 1 turns on, on second press Led 1+led 2 turns on, on third press led will flash, on forth pres light will go off.....ok??
You plug this switch to receiver to channel 3 , and then you control it with transmitter channel 3, the switch has 2 output, when you press 1x channel 3 on transmitter led 1 turns on, on second press Led 1+led 2 turns on, on third press led will flash, on forth pres light will go off.....ok??
Answered by Runner on 12/02/2022Helpful (0)
Ask a Question
1.You can contact the customer service. for any question regarding the product.
2.Ask the question in English to get answer faster.